Tools and materials:
Level
Boys Coat 8 Clearance
Drill with various bits
9 / 16 "key
Tape measure
Framing square
Channel lock pliers
Some notes before you begin:
1) Observe all local plumbing and building codes.
2) Before installing the new toilet you unpack and inspect it for damage. Back to the toilet to its protective carton until you are ready to install it.
3) These instructions are for installation on the water timber frameConstruction. For other installations, supply suitable bracing and fastening devices of sufficient size and strength.
4) The walls and floor must be square, plumb and level.
Pedestal sink installation guide
Step One:
1) Rough Trade in the exhaust pipe Note: This offer can not stop manages more than 3 "from the wall finish in the open position.
2) Install enough support behind the wall surface to provide a safe material for 'Anchoring.
3) Apply two adhesive seal (included) for each of the three bridges in the lower cavity of the toilet.
Tips to remember
1) Wash Room Selection: When replacing a toilet pedestal to keep in mind the color and style, additional criteria for selecting the piece for your bathroom or guest bathroom.
2) This device may expose the flaws in the wall and floor that complicate the installation.
3) If you do not want to touch the floor or somethingeasier to clean your system, try a wrapped Lav, they are as robust as the pedestal lav and give a nice open view of the room.
Step Two:
1) Mark the center line on the floor.
2) Insert the plug on the bottom line.
3) fix the toilet on the podium.
4) Place the base as necessary to ensure a proper fit in the desired position.
5) the Cabinet level. Add more self-seal as necessary to level the toilet. Note: The toilet must besupported by the base.
6) Check the placement of toilets.
7) Mark the center of each hole for the wall and mark the floor through the hole in the base down.
8) Carefully remove the toilet from its base. Then move the base in the area.
Faucet Selection: The unit must have enough free space between the cork layer and the wall.
Step Three:
1) Drill a ¼ "hole at the mark on the floor, then drill two ¼"Stock screw holes in signs on the wall.
2) Install bolts fixing the wall so about 1-1/4 "of each screw is exposed. Note: other fasteners of sufficient size and strength can also be used.
3) Install the faucet and drain the toilet after the manufacturer's instructions. Note: Do not tighten the connections exhaust slip-venture at this time.
The existing hardware: wc with pedestal sink, wall-mounted toilet or wrapped, have aconsiderable amount of hardware and sanitation suspended from his eyes. Make sure to close P supply lines and valves are acceptable for the appearance. This is a perfect time to change and uPDAte.
Before the installation: If you open the window (s), it is easy to verify that all parts are desired. There is a list of items in the instruction book.
You want to install the faucet and drain the toilet up, before you install the top. It iseasier to work with at this time and both sides are not too much weight.
Step Four:
1) The base mounting hole in the hole in the ground.
2) Place the base on the floor with the wood screw and washer. Pull the wood screw until it is tight.
Oops! Damage to the product: Do not overtighten. Turn the screw in wood can damage the product.
Step 5:
1) Set the toilet base so that the studs extend throughthe toilet hole.
2) the level of the toilet.
3) Install the nuts and washers and tighten until it stops. Oops! Risk of damage: Remove the cap nuts. Tightening could damage the product.
4) Close and remove the trap. Connect the hot water and cold water tap.
Installation Tips: If available, the installation is much easier with two people. Some of these toilets are very heavy and can move with difficulty. Mostimportant time to help you if you set the toilet and the mounting parts and food, the P-trap at the same time. It 'nice to have someone lifting and placing, while others lined pipes.
Install the legs of the wall is a relatively simple task. But when the threaded screw, a threaded connector rod to put the wires to protect them (another option is to use more nuts). This is much easier tightening the nutsKeep the lav.
installing a pedestal sink easy!: Old Gringo Diego Boots Best !: Cheap Canon Digital Rebel Xt Sale
No comments:
Post a Comment